View MP5016HGQH_8975988.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mp 5016h 2.7 - 22 v, 0.7 - 5a , current limit switch with over - voltage clamp and reverse block mp 5016h rev. 1.0 www.monolithicpower.com 1 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. description the mp 5016h is a protection device designed to protect circuitry on the output from transients on the input. the mp 5016h also protects the input from undesired shorts and transients coming from the output. during start - up, the inrush curr ent is limited by limiting the slew rate at the output. the slew rate is controlled by the dv/dt pin setting and mode pin setting . the maximum load at the output is current - limited. the magnitude of the current limit is controlled by an external resistor from ilimit to gnd. there is a fixed 2.5a current limit when ilimit is floating . the output voltage is limited by the output over - voltage protection ( ovp ) function . the clamp voltage can be set by the mode connection. the mp5016h offers a gate drive signal connect ed to an external n - channel mosfet gate to block current flow ing from the output to the input when the ic is in enable off , power shutdown , or thermal shutdown. the mp5016h is available in a qfn - 10 ( 1.5 mm x 2 mm) packa ge. features ? wide 2. 7 v to 22 v operating input range ? 26v absolute maximum transient input voltage ? selectable over - voltage clamp threshold ? fast output over - voltage protection ( ovp ) response ? integrated 4 3 m power mos fet ? adjustable current l imit or fixed current limit when floating ilimit ? reverse - blocking mos fet driver ? soft - start time programmable through dv/dt and mode ? fast response for har d short protection ? over - current protection ( ocp ) hiccup protection ? thermal shutdown and auto - retry ? available in a qfn - 10 ( 1.5 mm x 2 mm) package applications ? hdd, ssd ? hot swap s ? wireless modem data cards ? pc cards ? usb power distribution ? usb protection ? usb3.1 power delivery all mps parts are lead - free, halogen - free, and adhere to the rohs directi ve. for mps green status, please visit the mps website under quality assurance. mps and the future of analog ic technology are registered trademarks of monolithic power systems, inc. typical application i l i m i t g n d v c c d v / d t s o u r c e v i n v o u t e n e n g a t e m o d e c 1 1 f c 2 1 0 f m p 5 0 1 6 h l h o p t i o n a l m 1
mp5016h C 2.7 - 22v , 0.7 - 5a , programmable , current - limited swi tch mp 5016h rev. 1.0 www.monolithicpower.com 2 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all rights reserved. ordering information part number* package top marking MP5016HGQH qfn 10 ( 1.5 mm x 2 mm) see below * for tape & reel, add suffix C z ( e. g. MP5016HGQH - z ) top marking fg : product code of mp 5016h g qh l l: lot number package reference top view qfn - 10 (1.5 mm x2mm) 1 0 9 8 1 2 3 4 5 6 7 v c c v c c e n d v / d t g a t e s o u r c e s o u r c e m o d e g n d i l i m i t
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 3 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. absolute maximum ratings (1) v cc, source .............................. - 0.3v to 2 6 v mode ................................ ............ - 0.3v to 2 6 v gate ................................ ...... source + 5.5v all other pins ............................... - 0.3v to + 5.5 v junction temper ature ............... - 40 c to +150 c lead temperature ................................ .... 260 c continuous power dissipation (t a = + 25 c ) (2) (4) qfn - 10 ( 1.5 mmx 2 mm) ............................ 2.2 3 w recommended operating conditions ( 3 ) supply voltage ( v cc ) ..................... 2. 7 v to 22 v output voltage ( source ) .............. 2. 7 v to 22 v operating junction t emp . (t j ) ... - 40c to +125c thermal resistance ( 4 ) ja jc qfn - 10 (1.5 mm x 2mm ) ev5016h - qh - 0 0a (4) ............ 56 ....... 18 ... c/w jesd51 - 7 (5) ........................ 130 ...... 25 ... c/w notes : 1) exceeding these ratings may damage the device. 2) the maximum allowable power dissipation is a function of the maximum junction temp erature t j (max), t he junction - to - ambient thermal resistance ja , and the ambient temperature t a . the maximum allowable continuous power dissipation at any ambient temperature is calculated by p d (max) = (t j (max) - t a )/ ja . exceeding the maximum allowable p ower dissipation produces an excessive die temperature, causing the regulator to go into thermal shutdown. internal thermal shutdown circuitry protects the device from permanent damage. 3) the device is not guaranteed to function outside o f its operating conditions. 4) measured on ev5016h - qh - 00a , 2 - layer pcb , 50mmx50mm. 5) measured on jesd51 - 7, 4 - layer pcb.
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 4 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. electrical characteristics v cc = 5v, r limit = ns , c out = 10 f, t j = - 40c + 125c ( 6 ) , typical val ue is tested at t j = +25c unless otherwise noted. parameter symbol condition min typ max units supply current supply current (quiescent) i q en = high, mode = vcc/gnd/float 50 a en = high, mode connect resistor to gnd 90 a supply current (shutdown) i s en = gnd 9 a power mosfet on resistance r dson i out = 1a 43 m turn - on delay t delay dv/dt float, mode float 500 s off - state leakage current i off v cc = 12 v, en = 0v 0.1 1 a under - /over - voltage protection (uvp, ovp) under - voltage lockout rising threshold v uvlo 2.38 2.53 2.68 v uvlo hyst eresis v uvlohys 200 mv output over - voltage clamp voltage v clamp v mode = gnd , t j = 25c 5.5 5.75 6 v v mode = vcc , t j = 25c 14.2 15.2 16.2 v r m ode = 76. 8 k , v cc = 5v, t j = 25c 3.71 3.95 4.19 v r mode = 115 k , t j = 25c 5.3 5.7 6.1 v r mode = 324 k , t j = 25c 14.2 15.5 16.7 v r mode = 422 k , t j = 25c 18.2 20 21.8 v dv/dt dv/dt slew rate dv/dt dv/dt float, v mode = gnd 0. 4 0.8 1. 2 v/ms dv/d t float, v mode = vcc 1. 3 2 2. 7 dv/dt float, mode float 2. 8 3.8 4. 8 dv/dt current i dv/dt v dv/dt = 0.5v 4.5 6.5 8.5 a current limit current limit at normal operation i limit_no float ilimit , t j = 25c 2.3 2.5 2.7 a r limit = 604 , t j = 25c 3.3 3.5 3.7 a r limit = 3k , t j = 25c 0.6 0.75 0.9 a enable (en) enable rising threshold v en_rising 1. 86 2 2. 16 v enable hysteresis v en_hys 350 mv enable pull - down resistor r en_down 2.2 m gate gate maximum source c urrent i g_source_max i out = 1a 7 12 a gate maximum sink current i g_sink_max vcc = v source = 5.5v , v gate = 10.5v 1.3 ma
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 5 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. electrical characteristics (continued) vcc = 5v, r limit = ns , c out = 10 f, t j = - 40c + 125c ( 6 ) , typical value is tested at t j = +25c unless otherwise noted. parameter symbol condition min typ max units output discharge discharge resistance r dis vcc = 5v 540 otp thermal shutdown ( 7 ) t sd 175 c thermal hysteresis ( 7 ) t sd_hys 50 c notes : 6) not tested in production , guaranteed by over - temperature correlation . 7) g uarantee d by engineering sample characterization .
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 6 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. typi cal characteristics v in = vcc = 5v, v en = 5v, r limit = 604 ? , c out = 10 f , t a = 25c, unless otherwise noted.
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 7 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. typical performance characteristics v in = vcc = 5v, v en = 5v, r limit = 604 ?, mode float ing , dv/dt float ing , c out = 10 f, t a = 25c, unless otherwise noted.
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 8 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. typical performance characteristics (continued) v in = 5v, v en = 5v, r limit = 604 ?, mode float ing , dv/dt float ing , c out = 10 f, t a = 25c, unless otherwise noted.
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 9 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. pin func tions pin # name description 1, 2 vcc supply voltage . the mp 5016h operates from a 2. 7v to 22v input rail. a ceramic capacitor is required to decouple the input rail. connect vcc using a wide pcb trace. 3 gnd system ground . 4 ilimit current limit set . place a resistor between ilimit and ground to set the value of the current limit. float ilimit to achieve a 2.5a fixed current limit. 5 mode output over - voltage protection ( ovp ) clamp voltage select . the output ov p clamp voltage is selected by the mode connection . a resistor connected from mode to ground set s the ovp threshold voltage. t hree digital inputs are provided for mode . drive mode high to vcc to set the output ovp clamp voltage at 15.2 v . drive mode low to gnd to set the output ovp clamp voltage at 5. 7 5 v . float mode for no ovp clamp protection. 6, 7 source source of the internal power mos fet and output terminal of th e ic. 8 gate gate driver for reverse - current block mosfet. a 100pf ca pacitor is required on gate if the reverse - current block mosfet is not being used . 9 en enable. force en high to enable the mp 5016h . float en or pull en to ground to disable the ic. for quic k start - up, p ull en up to v cc through a 300 k? resistor. 10 dv/dt dv/dt . connect a capacitor from dv/dt to ground to set the dv/dt slew rate.
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 10 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. block diagram figure 1 : functional block diagram g n d c h a r g e p u m p l d o c u r r e n t s e n s e 1 v r e f i l i m i t s o u r c e d v / d t c o n t r o l l o g i c o v p e n 4 a 8 a 8 0 k v d d f a s t o f f c o m p c u r r e n t l i m i t a m p s o f t s t a r t t h e r m a l s e n s e 6 . 5 a s o u r c e l o g i c v d d l o g i c f o r i l i m i t f l o a t i n g v c c g a t e o v p l i m i t m o d e 2 . 2 m 5 . 5 v 1 k
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 11 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. operation the mp 5016h is de signed to limit the in rush current to the load when a circuit card is insert ed into a live backplane power source, thereby limiting the backplanes voltage drop and the d v /dt of the voltage to the load . the mp5016h offers an integrated solu tion that monitor s the input voltage, output voltage, output current, and die temperature , which eliminates the requirement of an external current sense power resistor, power mosfet , and thermal sense device. under - voltage lockout (uvlo) the mp 5016h ca n be used in a 2. 7 v to 22v input supply system. there are high - energy transients during normal operation or hot swap s . these transients depend on the parasitic inductance and resistance of the wire and the capacitor at t he vcc node. if a power clamp (tvs, tranzorb) diode is not used, the e - fuse must be able to withstand this transient voltage. the mp 5016h integrates a high - voltage mosfet with up to 22v of continuous voltage and 26 v of maximum transient input voltage. the mp5016h also uses a high - voltage circuit for the vcc node to guarantee safe operation. mode mode is used to select the output over - voltage protection ( ovp ) threshold. three digital inputs are provided for mode . drive mode high to vcc to set the output ovp clamp voltage at 15.2 v. drive mode low to gnd to set the output ovp clamp voltage at 5.75 v. float mode for no ovp clamp protection. the ovp threshold can also be set by con necting a resistor from mode to ground. for more detail s , refer to the application information section on page 13 . soft start (ss) the soft - start time is related to the dv /dt slew rate and input voltage and can be calculated with equation (1 ): (1) the dv /dt slew rate is controlled by an external dv/dt capacitor setting and the mode setting. fast output and input ovp to protect the downstream load when there is a surge voltage at the input, the mp 5016h provides an output ovp function. an accurate and fast comparator monitor s the over - voltage condition of the output. if the output voltage rises above the thresh old set by mode , the gate of the internal mosfets is pulled down quickly and is regulated to a certain value to keep the output voltage clamped at the ovp threshold. the fast loop response speed keeps the over - voltage ov ershoot small. current limit (ilimit) the mp 5016h provides a constant current limit , and the current limit can be programmed by an external resistor. t he desired cu rrent limit i s a function of the external current limit resistor and can be approximated with equation (2) : (2) where 3 870 is the current sense ratio . once the current limit threshold is reached, the internal circuit regulate s the gate voltage to hold the current in the power mos fet constant . to limit the cur rent, the gate to the source voltage must be regulated from 5v to around 1v. the typical response time is about 15 s . during this period , the output current may have a small overshoot. if the current limit condition lasts longer than 2m s , the ic enters hiccup mode with 2ms of on time and 700ms of off time. the mp 5016h allows ilimit to be float ed during operation. if ilimit is floating, the current limit is set a t a fixed 2.5 a internally. when short ing ilimit to gnd, the normal current limit is disabled , but the secondary current limit still works. the secondary current lim it is set to 8 a internally . when the secondary current limit is tri gg e re d , the ic shut s down the power mosfet. (v/ms) dv/dt vin(v) t_ss(ms) ? limit limit 0.55(v) i (a) 3870 r( ??
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 12 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. short - circuit protection (scp) if the load current increases rapidly due to a short - circuit event, the current may exceed the current - limit threshold before the control loop can respond. if the current reaches the 8 a secondary current limit level, a fast turn - off circuit activ ates to turn off the power mos fet . this can help limit the peak current through the switch, keep ing the input voltage fr om drop ping too much. the total short - circuit response time is about 1 s . after the mos fet has switched off, the part restart s . during the restart process, if the short still exist s , the mp 5016h regulate s the gate voltage to hold the current at a normal current limit level. t he ic enters hiccup mode with 2ms of on time and 700ms of off time. to prevent safe operating area ( soa ) damage during a high input voltage short - circuit protection ( scp ) condition, the ic current limit fold s back wh en the power mos fet v ds voltage is above the typical 11v and the junction temperature is over 110 c. to avoid large input voltage spike s from damag ing the ic during scp entry, it is recommend ed to use a 22 f minimum input capacitor when v in is higher than 15v. if the input surge voltage is higher than the 26v absolute voltage , the ic may be damaged . reverse - blocking mos fet driver the mp 5016h has a gate pin to provide an exte rnal n - channel mosfet gate drive signal for reverse - current protection (rcp) . three events can pull down the gate voltage : v in below the under - voltage lockout ( uvlo ) , the enable (en) voltage below the low level threshold , or thermal s hutdown. if any of these condition s occur , gate sink s the current from the gate of the external mosfet to initiate a fast turn - off. for 3.3v low input voltage application s , choose an external reverse - blocking mosfet wi th a small gate threshold voltage (v gsth < 1.6v) to reduce the voltage drop caused by the reverse - blocking mosfet. set ting an appropriate ovp threshold can also protect the reverse voltage (from the output to the input) when using an external n - chann el mosfet . when v out rises too high during normal operation, the mp 5016h source voltage is higher than the ovp threshold. in this c ase, the gate voltage is regulated to maintain the source clamped at the ovp thresho ld. this action protect s the reverse current from the high v out to the low v in . a 100pf capacitor is required on gate if it is not connect ed to the external mosfet. output discharge the mp5016h involves a discharge func tion that provides a resistive discharge path for the external output capacitor. the function is active when the part is disabled ( v in uvlo, en shutdown ) and is done in a very limited amount of time. when using the external reverse - current block mosfet, the output discharge path is block ed by the reverse current block mosfet. therefore, the output cannot be discharged when the reverse - current block mosfet is used . e nable (en) the mp5016h is ena bled when en is high . the mp5016h is disable d when en is low. floating en shuts down the mp5016h because there is an internal 2 .2 m? resistor pull ing en down to ground. for auto matic start - up, connect a pull - up resistor from vcc to en. en is clamped internally using a 5.5 v zener diode (see figure 2). connecting the en input through a pull - up resistor to v cc limits the en input curre nt below 100a to prevent damage to the zener diode. for example, when connect ing a 3 00k pull - up resistor to 22v v cc , i zener = ( 22v - 5.5 v) / 300k - 5.5v / 2.2m = 53 a. figure 2: zener diode between en and g nd when u sing a pull - up resistor to set the power - on threshold, avoid using a pull - up resistor that is too small to increase the operation al quiescent current. e n l o g i c 2 . 2 m e n g n d 1 k 5 . 5 v
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 13 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. thermal shutdown C auto - retry ther mal shutdown prevents the chip from operating at exceedingly high temperature s . when the silicon die temperature exceeds 175c, the entire chip shuts down , and en report s a fail mode. when the temper ature drops below its lower threshold ( typically 125c ) , the chip is enable again after a 700ms delay , typically.
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 14 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. application information setting the current limit the mp 5016h current limit value should exceed the normal maximum load current, allowin g for tolerances in the current sense value. the current limit is a function of the external current limit resistor. table 1 and figure 3 list examples of typical current limit values as a function of the resistor value. table 1 : typical current limit vs. current limit resistor ( 8 ) r limit (?) 3 000 1050 604 470 4 22 i limit (a) 0.7 5 2 3.5 4 .5 5 note : 8) the current limit in table 1 is a typical value for the reference design. figure 3 : current limit vs. current limit resistor the mp 5016h current limit can be programmed from 0. 7 a to 5a by connecting the correct resistor ( r limit ) . the current limit cannot be set too low, because the mp 5016h works in sleep mode when the load is lower than 0. 38 a , typical ly . the current limit logic is d isabled in sleep mode , also . setting the over - voltage clamp threshold drive mode high to vcc to set the output ovp clamp voltage at 15.2v . drive mode low to gnd to set the output ovp clamp voltage at 5. 7 5v. refer to table 2 to set the mode high/low digital voltage. table 2 : mode high/low digital voltage min. max. v mode _high vcc - 0. 2 v v mode _low 0. 2 v the ovp threshold can also be set by connecting a res istor from mode to ground. in this case, the ovp clamp threshold is given by equation (3) : (3) r mode should be above 68k?. for example, an r mode value of 76.8 k? can set the ovp clamp threshold to 3.9 v. when r mode is used, place a 39pf capacitor from mode to gnd . setting the soft - start time the soft - start time is related to the d v /dt slew rate and input voltage and can be calculated with equation (4) : (4) the d v /dt slew rate is controlled by the external dv/dt capacitor setting and mode setting. table 3 shows the d v /dt slew rate value when dv/dt is floating. table 3: d v /dt sle w rate value when dv/dt is float ing mode connection dv/dt slew rate (v/ms) low 0.8 high 2 float 3.8 r mode for case s with an external dv/dt capacitor , the d v /dt slew rate can be calculated with equation (5) : (5) see table 4 for the k 1 factor value . 0.3(v) (k r 0.047 (v) v mode clamp ? ? ? (v/ms) dv/dt vin(v) t_ss(ms) ? 7ms (v) v clamp (nf) c k1 ? 6.5 (v/ms) dv/dt dv/dt ? ?
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 15 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. table 4 : k 1 factor value at external dv/dt capacitor mode connection k 1 low 5. 7 5 high 15.2 float 27 r mode for example, when the external dv/dt cap is 47nf and r mode is 76 .8 k? , the d v /dt slew rate is 1v/ms. large output capacitor with large output capacitor s , if the charge current during soft start trigger s the current limit , the mp 5016h enter s hiccup mode when the current limit is triggered for 2ms.to avoid start - up failure with a large output capacitor, a proper dv /dt slew rate must be set during the soft start to avoid trigger ing the current limit . pcb layout guide lines efficient pcb layout is cri tical for stable operation . for best results, refer to figure 4 and follow the guidelines below. 1. place the high - current paths (vcc , vout) close to the device using short, direct, and wide traces. 2. place the input capacitors close to vcc and gnd . 3. connect the vcc and vout pads to a large vcc and vout plane respectively to achieve better thermal performance. 4. place a current - limit resistor close to ilimit . 5. place the dv/dt capacitor close to dv/dt . figure 4 : recommended layout design example table 5 is a design example following the application guidelines for the given specifications . table 5 : design example v in (v) 2.7 to 22 current limit (a) 3.5 dv/dt slew rate (v/ms) 3.8 the detailed application circuits are shown in figure 5 and figure 6 . the typical performance and circuit waveforms is shown in the typical performance characteristics section. for more detailed device applications, please refer to the related evaluation board datasheet . mode clamp r * 7 v 1 2 6 7 v c c e n d v / d t g a t e s o u r c e m o d e g n d i l i m i t v c c v c c s o u r c e g n d v c c t o p l a y e r b o t t o m l a y e r r 1 c 3 r 2 c 2 c 1 g n d c 4
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch mp 5016h rev. 1.0 www.monolithicpower.com 16 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication prohibited. ? 2017 mps. all r ights reserved. typical application circuits figure 5 : typical application circuit without reverse - current blocking mosfet ( 9 ) figure 6 : typical application circuit with reverse - current blocking mosfet ( 9 ) ( 10 ) not e s : 9) to avoid large input voltage spike s from damag ing the ic during scp entry, it is recommend ed to use a 22 f minimum input capacitor when v in is higher than 15v . 10) for 3.3v low input voltage application s , it is recommend ed to choose an external reverse - blocking mosfet with a small gate threshold voltage (v gsth < 1.6v) to reduce the voltage drop caused by the reverse - blocking mosfet. i l i m i t g n d v c c d v / d t s o u r c e v i n v o u t e n g a t e c 3 n s r 1 6 0 4 m o d e c 1 1 f c 2 1 0 f 1 , 2 3 4 5 6 , 7 8 9 1 0 m p 5 0 1 6 h r 2 3 0 0 k c 4 1 0 0 p f i l i m i t g n d v c c d v / d t s o u r c e v i n v o u t e n g a t e c 3 n s r 1 6 0 4 m o d e c 1 1 f c 2 1 0 f 1 , 2 3 4 5 6 , 7 8 9 1 0 m p 5 0 1 6 h r 2 3 0 0 k m 1
mp5016h C 2.7 - 22v , 0.7 - 5a, programm able, current - limite d switch notice: the information in this document is subject to change without notice. users should warrant and guarantee that third party intellectual property rights are not infringed upon when integrating mps products into any application. mps will not assume any legal responsibility for any said applications. mp 5016h rev. 1.0 www.monolithicpower.com 17 5/25/2017 mps proprietary information. patent protected . unauthorized photocopy and duplication p rohibited. ? 2017 mps. all rights reserved. package information qfn - 10 ( 1.5 mmx 2 mm) s i d e v i e w b o t t o m v i e w n o t e : 1 ) a l l d i m e n s i o n s a r e i n m i l l i m e t e r s . 2 ) l e a d c o p l a n a r i t y s h a l l b e 0 . 1 0 m i l l i m e t e r s m a x . 3 ) j e d e c r e f e r e n c e i s m o - 2 2 0 . 4 ) d r a w i n g i s n o t t o s c a l e . p i n 1 i d m a r k i n g t o p v i e w p i n 1 i d i n d e x a r e a r e c o m m e n d e d l a n d p a t t e r n p i n 1 i d 0 . 1 5 x 4 5 o t y p 0 . 1 5 x 4 5

▲Up To Search▲

Price & Availability of MP5016HGQH

	To Download MP5016HGQH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .